Follett 110CT400A/W Bedienungsanleitung

Installation, Operation and Service Manual Following installation, please forward this manual to the appropriate operations person.208597R06110CT400A/

Installing countertop dispensers 1. Position dispenser in desired location, mark dispenser outline on counter and remove dispenser. 2. Drill four 3

10. Apply a thick bead, approximately. 1/4" (6mm) diameter, of NSF listed silicone sealant (Dow-Corning RTV-732 or equivalent) 1/4" (6mm)

Installing Satellite-fill icemakers Models110CR400A/W 1. Install Satellite-fill icemaker following instructions in icemaker manual. 2. Run uninsul

2. Remove dispenser top front cover by removing two screws at bottom corners of cover, lifting cover slightly and pulling forward. 3. Remove icemak

User informationHow the dispenser worksFollett’s 110 series automatic load ice and water dispensers receive ice from Follett’s 400 lb (181kg)/day icem

Recommended weekly cleaning 1. Wash drain pan and grille with Solution A above. Rinse thoroughly. 2. Slowly pour solution of one cup (8 oz/237ml)

PURPLEBLKBLKBLKORANGEWHITEWHITESWTRBLURDORGRDRDSWITCHT-S TATBIN SIGNALMAIN POWERSWITCH4RELAY71PURTIMER1 2 3WHITEWHITEWHITEWHITEWHITEPURBLKICE MACHINEB

How unit works — SensorSAFE modelsSensorSAFE models provide “touchless” ice and water dispensing. When a container is placed within the actuation zone

Symptom 1. Does not dispense ice. 2. Does not dispense water. 3. Water runs continuously. 4. Dispense wheel rotates continuously. 5. Icemaker run

Troubleshooting SensorSAFE board and sensorsBoard guideLEDs, when illuminated, indicate the following: PWR (board power) CLN (cleaning, no disp

Follett CorporationEquipment Return PolicyFollett equipment may be returned for credit under the following conditions:1. The equipment is new and unu

20Lens/sensor troubleshooting 1. Turn dispenser power switch off. 2. Remove splash panel. 3. Disconnect wires from output terminal(s) (WTR, SOL,

Ice transport tube replacement Models 110FB400A/W, 110CR400A/W 1. Remove top and rear access panel from dispenser (lower front panel in freestandin

engaging pin3/16 (5mm) ice tube holeice hose mounting bracketice level control statice tube1"(26mm)22All units 9. Slip supplied hose clamp onto

well nutice levelcontrol statrubber grommetcontrol box assemblyice mounting hose bracketknurled screwhopper assemblyice level control statbin thermost

24Part # Description Reference502756 Cover, top front, 110 countertop (CT) 1502703 Cover, top front, 110 countertop unit with Satellite-fill icem

Part # Description Reference502057 Fastener, dispense chute bracket 1502356 Tube, water station 2502681 Cover, dispense chute 3501829 Switch

26Part # Description Reference502057 Fastener, dispense chute bracket 1502681 Cover, dispense chute (includes labels) 2502248 Chute and funnel,

Part # Description Reference500514 Thermostat, bin level 1502209 Switch, dispenser power 2502209 Switch, icemaker bin signal 2502242 Control bo

28Part # Description Reference501802 Baffle, ice 1501493 Wheel, dispense (includes drive bar, rotating agitator, threaded bar & rod) 2501494

29Part # Description Reference502598 Coil, chilled water (includes two 502599) 1502599 Fitting, water coil 2502600 Brackets, chilled water cani

3Before you beginSpecifications Field wiringInstallation Installing freestanding dispensers Installing wall mount dispensers Installing Satellite-fi

Solenoid dispense assemblyPart # Description Reference #501830 Solenoid, dispense 1 502040 Cotter pin 2502039 Linkage, solenoid (includes 502054

31

208597R0604/07801 Church Lane • Easton, PA 18040, USAToll free (800) 523-9361 • (610) 252-7301Fax (610) 250-0696 • www.follettice.com

Welcome to FollettFollett equipment enjoys a well-deserved reputation for excellent performance, long-term reliability and outstanding after-the-sale

SpecificationsElectrical 1. Models with Satellite-fill icemakers (110CR400A/W) Icemaker Max. fuse Dispenser Max. fuse Basic electrical:

Attention – Should local codes require a hard-wired connection and/or shielded wiring, eliminate the cord and plug(s) and follow the appropriate field

7Field wiring diagramsFreestanding dispensers and countertop dispensers with integral icemakersCountertop dispensers with Satellite-fill icemakersXXEl

Installation proceduresInstalling freestanding dispensers 1. Carefully tip dispenser back to expose underside and block up in place. 2. Remove leg

12. Verify that water sensor tabs are immersed in water in reservoir.13. Remove top front cover by removing two screws at bottom corners of cover. L